Buick Through The Years.


This is the description of the photo above.
This northeast view is from 1947.
This north view is from 1930.
Back of above photo. follow link for a final view from June 7, 2000:

Buick City June 7th, 2000

Advertisements

Buick’s Second Main Office.

Here is a nice photo showing good detail of the east addition. Added in 1955. Link for this announcement.  The 1916 building announcement
October 4, 1917 article.
Here you can see it from the west end. That is factory #04 shown at the left. Factory #01 is still standing behind the office, so I know this is previous to 1963.
This shows the addition added to the east end of the office on Hamilton Avenue in 1955. 
An aerial view from 1920 shortly after the main office was built. That is it in the center foreground north of Hamilton Avenue.
Add caption
A closer view of the photos below with a good view of the bridges connecting with factory #01.
A close up of the photo below.
Taken from St Johns st. looking directly west up Hamilton ave.
August 25, 1927 in front of the Buick main office in Flint on Hamilton Avenue.
With factory #01 shown at the right. Facing north-west. 
I have many photos of the office.


Buick’s main office in 1919. It was built on the same site as the first office on Hamilton Avenue. You can see a small portion of the guard shack at lower left corner. The view is facing northeast.
Date of above photo.

 follow links:

Main Office Building First & Second

Buick Main Office

THE FACTORY BEHIND THE CAR

Liberator Engine work at Buick.


Liberator advertisement from during the war.
Looks like a master die maker and his apprentice making a combustion chamber core.
Die and core for the valve area.
Die and core for a combustion chamber.
A master die maker at work. The aluminum foundry was one of the few factories to have it’s own die shop “in-house”.
This looks like one of the early test molds because of the crude way they are doing it. This could even be at factory #70 where the training took place early in 1942.
These wires were what kept the delicate cooling fins made of sand from collapsing during the molding process. After all the wires were in place, the rest of the mold was filled until it was flush.
The workers became very fast at inserting all the hundreds of wires for each mold.
Putting a finished mold together.
Compressing a new core. You always needed the other half of the mold.
Compressing a new core.
Making the new cores.
Making the cores before baking in the special ovens.
Just as any other casting, there was usually more than one part needed to make up the cavities.
Working on a special inner core. It took a lot of trial and error to get things right.
Inner cores made up.
Making a mix. Aluminum scrap could only be re-melted a few times before it was as brittle as glass when cured.
Slag removal.
Making ingots.
Making the aluminum ingots, so you had a precise amount ready for each pour.
Freshly made molds will be lined up for easy pouring.
Freshly poured.
Making a pour.
Filling another ladle.
Making a pour.
Filling another ladle.
The pouring of aluminum was a very precise operation. It had to be just the right temperature and consistency. It poured like syrup which was nothing like pouring iron.
This is where the ladle was placed between pours.
Opening another mold.
Opening a newly made head. In the early beginnings of this operation, you never knew what would be inside. Once they got all the heat cycles and such right, they were turned out by the thousands. The total was 3,120,000 to be exact.
I think this was called the “Blast Machine” and was used for checking the new casting for defects and also cleaning out.
Reclaiming core sand entered here. The steel wires used for supporting the delicate cooling fins made of sand were separated by magnets.
Sand drying area. Also delivery of reclaimed sand, which was one of the main benefits of this whole new operation.
Sand delivery crane.
Bins for coarse and fine sand.
A band-saw makes quick work of removing much unwanted material.
A band-saw makes quick work of removing much unwanted material.
A band-saw makes quick work of removing much unwanted material.

A band-saw makes quick work of removing much unwanted material.
Fine grinding the base of the head.
Heads entering the heat treating oven.
Air aging area. I tried to figure out the procedure here, but I’m still not sure.
One of many air aging turntables.
Loaded on the turntable for age curing.
Either ready for the air aging area or already done.
After all curing is done they are on the way to the finish and cleaning area.

Automated milling machines.
Automated milling machines.
Automated milling machines.
Not sure of this one yet.
Not sure of this one yet.
May be the “Jolt Squeeze machine”.
May be the “Jolt Squeeze machine”.
Buffing the heads.
The tools needed for the finish work.
Hand work with a saw.
Hand working with grinders and other tools.
Hand working with grinders and other tools.
Hand working with grinders and other tools.
Hand working with grinders and other tools.
Cleaning station.
Cleaning station.
Automatic packer for the heads.
Heads ready for the trip to the Buick assembly plant in Melrose Park Illinois.
follow the links:

Buick At It’s Battle Stations

World War II Archeology in England

B-24 Liberator

Factory #40 Description + Display

Another view inside factory #08

Factory #05/#10 War Work

Factory #10

Buick WWII First Metal July 17,1942

Buick Service Department.

The old Imperial Wheel Company became Buick’s service department in 1916. Chevrolet built cars here between 1912-1914. In 1915 the Monroe Motor Company used the building , it was demolished in 1938. Then Buick built their new Service and Parts building #84 on this site. It would become the engineering building for Buick in 1947. follow the links:

Imperial Wheel Company Had Many Faces

Building #84 Service And Parts

Industrial and Hamilton Avenue

Looking north from Hamilton Avenue with the Buick axle factories #31, 32 and 33 along Industrial Avenue. Factory #38 is visible in the far distance. The first part of this factory (until the roof height changes) was the original Weston-Mott axle factory built in 1906. In 1906 just the front portion was a two story structure. The part running along Industrial was but a single floor factory at that time. The center section remained a single floor factory with just the east and west wings being built with a second floor. The new door added off to the right of the truck parked near the sign, was, ‘I believe’ where you hired in at one time. Beginning in 1940 the new axle factory #31 was built at the corner of Leith street and Industrial Avenue. It was built on the site of old factory #16 demolished in 1939. This photo is dated April 3, 1934. additional links:

Factory #38 Axle Machine Shop + Hamady Store

Factory #31 Postcard

Factory #31 During Construction

Factory #16 Demolition 1940

Inside Weston-Mott

Weston Mott 1906-1910